Sales: 1-607-698-4430
Fax: 1-607-698-4434
Rhino Machine

Built specifically for the Glazing Industry

The Rhino 900 is designed and built specifically for the glazing industry by people who know the industry and the special requirements of fabricating curtain wall and storefront.

  • We understand that you could be fabricating 10” curtain wall in the morning and storefront in the afternoon and anything else in between
  • We understand that a rush job means now and not next week
  • We understand that when you need our support it is this minute and not tomorrow
Rhino Machine

Layout, Drill and Cut at the same Location

No more layout of drilling locations with a tape measure and pencil, no more drilling templates. The Rhino is fed the layout from the elevations that are already drawn, it knows exactly where to drill and cut the parts.

  • No more movement of material from one workstation to another
  • Eliminating material movement cuts down on scratches and damage to the material
Rhino Machine

Load the machine for constant use

With our automatic material loading and feed center you can load your material and let the machine run for hours. This cuts down on loading time significantly.

  • Load 10 stock lengths up to 32’ at once
  • Let the machine operator concentrate on running the machine
  • Allows the operator the ability to pay attention to sorting and stacking the material on the out feed
  • Reduces the need for 2 men at the machine, one man operation
  • Always a continuous flow of material going to the machine
Rhino Machine

Accurate cuts and holes insure an exact fit every time

The Rhino cuts and drills within .5000 of an inch, this insures accurate cuts and holes so your horizontals line up with your verticals exactly.

  • Auto sighting to insure deflected pieces are drilled correctly the entire length of the extrusion
  • Drill and countersink at required locations
Rhino Machine

3 Drill Heads insure rapid drilling of holes

3 Drill Heads insure rapid drilling of holes With a drill at the top, bottom and front of the machine working together the Rhino drills holes faster than traditional CNC machines

  • Drill Vertical screw spline and shear block holes on the top and bottom simultaneously
  • Drill and countersink horizontal shear block holes from front drill
  • Drill holes on front of vertical for steel loaded mullions
Rhino Machine

Pre-Loaded parts

We have most manufacturers parts preloaded into the software that runs the machine, this saves thousands of hours of work loading parts. We constantly add manufacturers and their parts to the database. We maintain the database so you can concentrate on your work.

  • YKK-API
  • Efco
  • Kawneer
  • Tubelite
  • Old Castle
  • US Aluminum
Rhino Machine

Load your own custom parts and Fabrications into the software to go to the machine

You can load any part and fabrication into the software to draw elevations with or just simply to send an extrusion to the machine for quick machining. The software is very powerful and flexible for our type of work.

  • Load parts fast and easy
  • Load fabrications fast and easy
Rhino Machine

The Rhino 900 verses traditional CNC machines

The Rhino 900 was designed and built specifically for the curtain wall and storefront industry; our needs are complex and vary greatly from project to project. While other CNC machines do much more and serves more industries our machine does exactly what you need done.

  • The machine takes a cut list and fabrication and drills and cuts
  • You don’t need an expensive and highly trained CNC operator to run the machine
  • Very fast start up with the machine, you are doing a project the day they install the machine
  • Very easy to operate
Rhino Machine

Very low cost, the machine pays you to own

The Rhino 900 literally pays you to own, with your signature you can start earning money with the Rhino immediately. The machine will earn you at least 26.00 dollars an hour, we ask that you only give us a part of that so we can continue to build the best machine. After 5 years you keep 100% of the profits. The machine with proper maintenance will last you 10-15 years at least.

  • Very low cost to own the machine
  • This machine is accepted for Section 179 tax break, this means you can deduct the entire amount of the machine this year on your taxes and still deduct the payments for the following 5 years. An easy 40-60,000 in your pocket this year.
  • In most states there is no Sales Tax
Rhino Machine

Automatic Sorting of material as it comes off the machine

Sorting of cut material has always been a process that takes a lot of time and effort, we automatically sort the materials for your carts to allow the operator to know where the parts go as they process materials through the machine.

  • Sort for Carts as it comes off the machine
  • Sort by elevation
  • Sort by tag or mark number
Rhino Machine

Turn Key installation and Setup

The Rhino 900 installs in 3 days by our highly trained staff, once the machine is setup then they run a project at your location and train your staff in its operation. By the time we leave you will be running projects daily with the machine.

  • Installation and training done by highly trained staff
  • Setup and running in 3 days
  • Software training is done prior to machine installation
  • Ongoing software training provided
  • No CNC experience required to operate the machine
  • Easy and fast to train new employees to operate the machine
Rhino Machine

20” Upcut Saw

Our 20” upcut saw is a straight cut saw that gets the job done, (optional compound miter saw with positioner)

  • Compound Miter Saw and positioner on outfeed side of machine
  • 20” Upcut saw standard with machine
  • Cuts within .005 (5/1000th of an inch) for accurate cuts every time
  • Adjustable blade height or travel to save time on smaller parts
Rhino Machine

One Man Operation

The Rhino is a one man operated machine

  • One man operation
  • Expand your business without adding employees
Rhino Machine

Made In USA

Our equipment and software is made right here in the USA with pride. Getting parts for the machine or support for the software is very quick and easy

  • Made in Arizona
  • Supported in Arizona
Rhino Machine

Excellent Fanatical Support

When I say Fanatical support I really mean fanatical support, you call we answer. We are here to answer your questions or go online to help with your project immediately. We understand when you have a job now that means Right Now!!!

  • Never get a machine, we answer
  • Get immediate help with issues
Rhino Machine

Direct connect Software to Machine

Design all your frames with parts in our software and send directly to the machine for fabrication. Our software is the best in the industry for designing curtain walls, storefronts and sending out to fabrication

  • Manufacturers come preloaded
  • Load your own custom parts and fabrications
  • Create custom frames, Arched Top, Rake Top, Corners etc…
  • Create project estimates
  • Glass takeoffs
  • Bill of Materials
  • Perform alternate bids(Switch from one manufacturer to another for pricing)
  • Export to CAD